亚洲无码电影院高清在线播放,黄色入口亚欧三级,草榴视空姐,亚洲VR一区二区在线播放,无码中文字幕av免费放,国产一区二区精品偷斗情

歡迎您進入深圳長欣自動化設備有限公司

長欣工控

plc控制器 ? plc控制系統 ? plc控制柜

工控設備供應商

咨詢熱線177-5963-5229

prevnext

ABB UFC721AE 3BHB002916R0001 控制板驅動板主板

    價格:聯系客服
    質保:1年
    售賣地區:全國
    上架日期:2024-05-06 15:00
  • 咨詢熱線:177-5963-5229
  • 產品詳情

ABB  UFC721AE 3BHB002916R0001  控制板驅動板主板

ABB  UFC721AE 3BHB002916R0001  控制板驅動板主板

ABB  UFC721AE 3BHB002916R0001  控制板驅動板主板

ABB 3BHB002916R0001 UFC721AE (1).jpg

產品詳情資料:



3BHB002916R0001 UFC721AE


在步驟5中,傳輸編程后,設置DGCS中的GO位。如果由于PCI_CSR中的BM位未設置為啟用PCI總線主控權,或者源和目標起始地址未對齊,DMA編程不正確,則將斷言P_ERR。否則,將設置ACT位,然后DMA將開始傳輸數據,與PCI目標和中斷通道共享VMEbus的所有權,與VMEbus從屬通道共享PCI總線的所有權。在步驟6中,等待DMA傳輸?shù)慕K止。DMA將繼續傳輸,直到:?完成所有傳輸,?使用STOP_REQ位提前終止,或?在PCI總線或VMEbus上遇到錯誤。這些條件中的每一個都將導致ACT位清零,并在DGCS寄存器中設置相應的狀態位。如果在步驟1中啟用,也將生成中斷。一旦軟件設置了GO位,軟件就可以通過等待中斷生成或輪詢狀態位來監控DMA完成。建議還啟動后臺計時器以使傳輸超時。這將確保DMA沒有被繁忙的VMEbus或其他此類系統問題掛斷。

ABB 3BHB002916R0001 UFC721AE (7).jpg

產品英文詳情料:



In Step 5, with the transfer programmed, the GO bit in DGCS must be set. If the DMA has been improperly programmed, either because the BM bit in the PCI_CSR has not been set to enable PCI bus mastership, or the source and destination start addresses are not aligned, then P_ERR will be asserted. Otherwise, the ACT bit will be set, and the DMA will then start transferring data, sharing ownership of the VMEbus with the PCI Target and Interrupt channels and the PCI bus with the VMEbus Slave Channel. In Step 6, one waits for termination of the DMA transfers. The DMA will continue with the transfers until it: ? completes all transfers, ? is terminated early with the STOP_REQ bit, or ? encounters an error on the PCI bus or VMEbus. Each of these conditions will cause the ACT bit to clear, and a corresponding status bit to be set in the DGCS register. If enabled in Step 1, an interrupt will also be generated. Once the software has set the GO bit, the software can monitor for DMA completion by either waiting for generation of an interrupt, or by polling the status bits. It is recommended that a background timer also be initiated to time-out the transfer. This will ensure that the DMA has not been hung up by a busy VMEbus, or other such system issues.

ABB 3BHB002916R0001 UFC721AE (6).jpg

ABB Honeywell Woodward

CS31 ECZ FPR3700001R0001 C7076A1015 9905-463

ICSI16E1 FPR3316101R1032 C7061F2001 5463-785

ICSK20F1 FPR3327101R1202 ACX633 51196655-100 5463-473

PP836A 3BSE042237R2 ACX631 51198947-100 5464-414

3BHB004744R0010 XVC517 942-M0A-2D-1G1-220S 5464-544

NGPS13C  3AUA0000042489 942-A4M-2D-K220S 5463-581

PP235 3BSC690102R2 900H03-0102 5464-013

DSTD110A  YB161102-AM 900G32-0001 5464-211

ABB 3BHB002916R0001 UFC721AE (5).jpg

ABB 3BHB002916R0001 UFC721AE (4).jpg



咨詢:ABB UFC721AE 3BHB002916R0001 控制板驅動板主板

*為必填項

*聯系人
*手機號碼
*郵箱
咨詢內容

返回頂部

德保县| 商洛市| 罗城| 泽普县| 阿拉善左旗| 义乌市| 汽车| 大丰市| 庐江县| 邹平县| 合肥市| 海门市| 武安市| 武邑县| 成安县| 阳朔县| 沅江市| 平潭县|